Click Add Groups and enter the name you would like to give client VPN permission to.įrom the list of conditions, select the option for NAS-Port-Type.
Setup anyconnect vpn access on radius server windows#
In the Network Policy Wizard enter a policy name and select the network access server type unspecified, then press Next.Ĭlick Add to add conditions to your policy.įrom the list of conditions, select the option for Windows Groups. In the left-side pane of the NPS server console, right-click the Network Policies option and select New. Press Next on the next three pages of the wizard to leave the default settings intact. Access-request messages will need to meet these conditions to be allowed access.įrom the list of conditions, select the option for NAS-Port-Type.
In the Connection Request Policy Wizard, enter a policy name and select the network access server type unspecified, then press Next.Ĭlick Add to add conditions to your policy. Right-click the Connection Request Policies folder and select New. In the NPS server console, navigate to Policies > Connection Request Policies. Note: Currently only ASCII characters are supported for RADIUS shared secrets, unicode characters will not work correctly.įor additional information or troubleshooting assistance, please refer to Microsoft documentation on RADIUS clients. Over VPN: use the IP address of the MX/Z on the highest-numbered VLAN in VPNĬreate and enter a RADIUS Shared Secret (make note of this secret, you will need to add this to the dashboard). Over a static route: use the IP address of the MX/Z on the subnet shared with the next hop On a local subnet: use the IP address of the MX/Z on the subnet shared with the RADIUS server This IP will differ depending on where the RADIUS server is located: Right-click the RADIUS Clients option and select New.Įnter a Friendly Name for the MX security appliance or Z teleworker gateway RADIUS client.Įnter the IP address of your MX security appliance or Z teleworker gateway.
In the left-side pane, expand the RADIUS Clients and Servers option. Open the NPS server console by going to Start > Programs > Administrative Tools > Network Policy Server. In order for the MX to act as an authenticator for RADIUS, it must be added as a client on NPS. Enter in the IP address of the RADIUS server, the port to be used for RADIUS communication, and the shared secret for the RADIUS server.Īdd MX security appliance as RADIUS clients on the NPS server. Click Add a RADIUS server to configure the server(s) to use. Use this option to authenticate users on a RADIUS server. Save your configuration and attempt to connect to the VPN to verify configuration. Upload the SAML metadata xml file provided by your Identity provider to the MX. Please ensure your An圜onnect URL starts with seen from DUO IdP below.Ĭonfigure your An圜onnect Server on the MXĬonfigure your An圜onnect URL - (add “:port” to the end of the hostname if using a port other than 443) SP Entity ID: /saml/sp/metadata/SAMLĪCS URL: /saml/sp/acsĮnsure to add “:port” to the hostname when using any port other than the default 443, e.g :8443, when referencing the An圜onnect Server in your configurationĪfter configuration, your identity provider will provide you with a SAML metadata file. If my An圜onnect Server hostname is " ", my DUO configuration for Entity ID and ACS URL will be configured as seen below: Select configuration of a new Generic/Custom Application, ( do not use An圜onnect presets in DUO for MX configuration)Ĭonfigure only the Entity ID and ACS URL as follows:Į.g. MX running An圜onnect), Identity Provider - DUO and a User.Ĭonfigure your Identity Provider - IdP (DUO) To setup SAML authentication, you need a Service provider (e.g. The directions below do not include configuration of an authentication source, which is a requirement if using DUO as an Identify provider. To configure An圜onnect on the MX Appliance to authenticate with DUO via SAML, see below. Setting up An圜onnect Authentication with Okta
0 kommentar(er)
